***** ALERT - Nominations for your new ClubCJ Committee can be made here *****
Install of carbon gauge cluster.
Moderators: Moderators, Senior Moderators
Re: Install of carbon gauge cluster.
Good news.
- adamhumphrey
- Lancer VRX/GTS
- Posts: 475
- Joined: Fri Jan 01, 2016 11:31 am
- Location: Rutherford NSW, Australia
Re: Install of carbon gauge cluster.
Yeah it is. The only thing stopping me is I’m not sure if I have to use sealant on the sensor. I read online people recommended to use permatex red thread sealant I can’t find it in stores anywhere local. So I might have to order some online
![Image](http://i.imgur.com/ZlQUYL5.jpg)
MY11 Evo X MR (2011-Current)
MY20 Asx GSR (2023-Current)
MY11 Peugoet 207 XT HDi (2020-Mar 2023)
MY09 Lancer Sportback VRX (2015-2019) - Sold Nov 2019
Owner Operator: - Adam's Attention to Detail. Mobile Detailing and Automotive Installations.
https://www.facebook.com/AdamsAttentionToDetail/
- lancerdarryl
- Lancer MASTER
- Posts: 1929
- Joined: Wed Jul 14, 2010 3:10 am
- Location: Newcastle NSW Australia
Re: Install of carbon gauge cluster.
A couple of wraps of thread tape will be ok or Stag jointing paste or grey Threebond.
Evolution X MR+ Lancer VRX Sportback +LA Lancer GSR
"Don't back off until you hit something"
"Don't back off until you hit something"
- adamhumphrey
- Lancer VRX/GTS
- Posts: 475
- Joined: Fri Jan 01, 2016 11:31 am
- Location: Rutherford NSW, Australia
Re: Install of carbon gauge cluster.
No worries, I'll give it a go thanks mate. I am just hoping I don't lose to much coolant from swapping it out.
![Image](http://i.imgur.com/ZlQUYL5.jpg)
MY11 Evo X MR (2011-Current)
MY20 Asx GSR (2023-Current)
MY11 Peugoet 207 XT HDi (2020-Mar 2023)
MY09 Lancer Sportback VRX (2015-2019) - Sold Nov 2019
Owner Operator: - Adam's Attention to Detail. Mobile Detailing and Automotive Installations.
https://www.facebook.com/AdamsAttentionToDetail/
- lancerdarryl
- Lancer MASTER
- Posts: 1929
- Joined: Wed Jul 14, 2010 3:10 am
- Location: Newcastle NSW Australia
Re: Install of carbon gauge cluster.
Get your new sensor ready within reach,remove the old one with one hand and stick your finger in the hole then grab the new one with your free hand and screw it in. Depressurise the radiator but leave the cap on this will minimise coolant loss.
Evolution X MR+ Lancer VRX Sportback +LA Lancer GSR
"Don't back off until you hit something"
"Don't back off until you hit something"
- adamhumphrey
- Lancer VRX/GTS
- Posts: 475
- Joined: Fri Jan 01, 2016 11:31 am
- Location: Rutherford NSW, Australia
Re: Install of carbon gauge cluster.
Ok, update on the car, it's all fixed now. I ended up ordering some Loctite 567 thread sealer. I was told its equivalent part is the Permatex stuff. To get the sensor out wasn't too much of a pain. I had them take out the rear fuel line bracket to allow a little bit of movement to get an extended 19mm socket in there. Thanks, @lancerdarryl for the advice about the coolant loss. I had it in the garage and fairly level. I had no coolant loss at all. Plugged in laptop cleared the code and gauge works again. I am off to get a new bung welded into the exhaust the old one stripped out when I attempted to remove it. So once that is done, I'll post up some pictures of the gauges all working.
![Image](http://i.imgur.com/ZlQUYL5.jpg)
MY11 Evo X MR (2011-Current)
MY20 Asx GSR (2023-Current)
MY11 Peugoet 207 XT HDi (2020-Mar 2023)
MY09 Lancer Sportback VRX (2015-2019) - Sold Nov 2019
Owner Operator: - Adam's Attention to Detail. Mobile Detailing and Automotive Installations.
https://www.facebook.com/AdamsAttentionToDetail/
Who is online
Users browsing this forum: No registered users and 13 guests