***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

braided lines, good idea?

All Brake Modifications.

Moderator: Senior Moderators

User avatar
darren1011
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 348
Joined: Sat Feb 11, 2012 10:48 am
Location: Wollongong, Australia

braided lines, good idea?

Postby darren1011 » Thu Oct 18, 2012 4:15 pm

Does anyone have an opinion on whether it's worth putting braided lines on an N A lancer if I'm just upgrading the rotors and pads, not bigger rotors or changing calipers. I'm on limited funds but seems to me the stopping power is something I would like to improve and my brakes tend to fade quick when I push it a bit. I already have new gas shocks, kings 30 mm, and whiteline sway bars to put on, and just picked up a set of 18x7 rims (off a Holden) for 100 bucks. New centre caps and I'm off. I'm thinking DBA 2201s rotors and QFM HPX pads

User avatar
Kal777
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 404
Joined: Mon May 21, 2012 9:48 pm
Location: Adelaide

Postby Kal777 » Thu Oct 18, 2012 7:14 pm

i would spend the money on a higher performing brake fluid and flushing out the stock dot3. maybe use some penrite super dot 4. has a higher boil point so the fluid will stay consistent for longer.
Image
Injen Cold Air Intake/K&N Invert Pod/BC BR Coilovers/Whiteline Strut Brace/DrIft Blade seats/Penrite HPR5/Penrite ProGear/PBR Gold Dot

User avatar
sleeper
Alumni
Alumni
Posts: 8259
Joined: Fri Apr 23, 2010 10:14 am
Location: brisbane
Contact:

Postby sleeper » Thu Oct 18, 2012 7:45 pm

road/sport pads and a high temp fluid will pull u up nicely :)
no need for new rotors imo unless your planning on some track work.
210 KWATW 400nm RALLIART Virtual Dyno 1/1
http://goo.gl/GrUosm


Image

User avatar
darren1011
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 348
Joined: Sat Feb 11, 2012 10:48 am
Location: Wollongong, Australia

Postby darren1011 » Thu Oct 18, 2012 7:47 pm

Kal777 wrote:i would spend the money on a higher performing brake fluid and flushing out the stock dot3. maybe use some penrite super dot 4. has a higher boil point so the fluid will stay consistent for longer.

I was going to do that already, didn't realise they only put dot3 in standard, but the front rotors have started to warp anyway, so I have to do them

User avatar
sleeper
Alumni
Alumni
Posts: 8259
Joined: Fri Apr 23, 2010 10:14 am
Location: brisbane
Contact:

Postby sleeper » Thu Oct 18, 2012 7:48 pm

warp?, i doubt it, what are the brakes doing to make u think the rotors are warped?
210 KWATW 400nm RALLIART Virtual Dyno 1/1

http://goo.gl/GrUosm





Image

User avatar
darren1011
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 348
Joined: Sat Feb 11, 2012 10:48 am
Location: Wollongong, Australia

Postby darren1011 » Thu Oct 18, 2012 7:51 pm

sleeper wrote:warp?, i doubt it, what are the brakes doing to make u think the rotors are warped?

Heavy vibration at anything more than light pressure. It's worse than a wheel alignment problem, which I suppose is what you're thinking. This car has done 85k, it's not a new car

User avatar
sleeper
Alumni
Alumni
Posts: 8259
Joined: Fri Apr 23, 2010 10:14 am
Location: brisbane
Contact:

Postby sleeper » Thu Oct 18, 2012 7:59 pm

my brakes had vibration after they were overheated, and as soon as they even got warm again, same thing by using the stock pads, new better pads fixed all that, i`d try new sport pads and high temp fluid before i went to the expense of new rotors, but if theyre worn sure change them
210 KWATW 400nm RALLIART Virtual Dyno 1/1

http://goo.gl/GrUosm





Image

User avatar
darren1011
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 348
Joined: Sat Feb 11, 2012 10:48 am
Location: Wollongong, Australia

Postby darren1011 » Thu Oct 18, 2012 8:03 pm

sleeper wrote:my brakes had vibration after they were overheated, and as soon as they even got warm again, same thing by using the stock pads, new better pads fixed all that, i`d try new sport pads and high temp fluid before i went to the expense of new rotors, but if theyre worn sure change them

I fihure wtf, get it all done at once and save on labor, shocks and springs, while the fronts are out, get teh CAI put in, have nothing to worry about for another 85k in terms of stopping, and move on to the exhaust, then maybe a few cosmetics. I have to keep the car 5 years, so might as well go the whole hog

User avatar
Mizta B
Alumni
Alumni
Posts: 5867
Joined: Sun Dec 21, 2008 8:29 am
Location: Mortdale, NSW, Australia

Postby Mizta B » Thu Oct 18, 2012 8:06 pm

Braided lines do have their advantages - due to the fact that they do not swell under pressure like rubber lines when pushed hard, they keep your pedal pressure positive all the time especially if you track your car
DBA rotors are a cost effective upgrade and a higher temp fluid and some decent pads eg Bendix Ultimates or QFMs is a good idea
Cheers Chris.
Australasian Gerbil Rearers Organisation, Official Re-Seller.
Image
MY09 Rally Red VRX ClubCJ's 1st 4B12 2.4L - CCJ Lifetime Member #0004.
Merlinised....

User avatar
darren1011
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 348
Joined: Sat Feb 11, 2012 10:48 am
Location: Wollongong, Australia

Postby darren1011 » Thu Oct 18, 2012 8:11 pm

Mizta B wrote:Braided lines do have their advantages - due to the fact that they do not swell under pressure like rubber lines when pushed hard, they keep your pedal pressure positive all the time especially if you track your car DBA rotors are a cost effective upgrade and a higher temp fluid and some decent pads eg Bendix Ultimates or QFMs is a good idea Cheers Chris.

Thanks, good info

User avatar
Mizta B
Alumni
Alumni
Posts: 5867
Joined: Sun Dec 21, 2008 8:29 am
Location: Mortdale, NSW, Australia

Postby Mizta B » Thu Oct 18, 2012 8:19 pm

No worries I have done a full upgrade on my VRX including Ralliart front calipers it stops really well :mrgreen:
Australasian Gerbil Rearers Organisation, Official Re-Seller.

Image

MY09 Rally Red VRX ClubCJ's 1st 4B12 2.4L - CCJ Lifetime Member #0004.

Merlinised....

User avatar
darren1011
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 348
Joined: Sat Feb 11, 2012 10:48 am
Location: Wollongong, Australia

Postby darren1011 » Fri Oct 19, 2012 12:04 am

Mizta B wrote:No worries I have done a full upgrade on my VRX including Ralliart front calipers it stops really well :mrgreen:

I'd love to go that way, but the money is an issue and I don't like to do work on the brakes myself, if they fail, I want to have someone to yell at

User avatar
Chubb
Post Monster
Post Monster
Posts: 2615
Joined: Fri Oct 16, 2009 8:04 am
Location: Uralla, NSW, Australia

Postby Chubb » Fri Oct 19, 2012 9:36 am

Just be warned if you have a VRX, some parts listings will say the VRX and RA have the same rotors but this is in fact incorrect for the front at least.

User avatar
darren1011
Lancer VRX/GTS
Lancer VRX/GTS
Posts: 348
Joined: Sat Feb 11, 2012 10:48 am
Location: Wollongong, Australia

Postby darren1011 » Fri Oct 19, 2012 9:42 am

adamvrx08 wrote:Just be careful which braided lines you get, you need to make sure they are ADR approved with a coating over the braid, otherwise it can be a defect.

I am thinking GSL, not the cheapest I've found, but state they ar ADR approved


Return to “Brakes”

Who is online

Users browsing this forum: No registered users and 5 guests